ماژول 6875 یک تایم سرور GPS در یک محفظه جمع و جور آلومینیومی برای نصب در ریل 35 میلی متری است. این ماژول دارای دو رابط شبکه 10/100/1000 طبق شرح ذیل میباشد: 2 ethernet interfaces 10/100/1000 Mbit/s...

تایم سرور 8029NTS کاملاً بدون تعمیر و نگهداری و هماهنگ سازی کلاک شبکه جهت نصب بصورت DIN Rail و بهترین راه حل هماهنگ سازی شبکه ها و برنامه های صنعتی استسرور NTP مستقل به طور...

سیستم ساعت و تایم سرور جهت صرفه جویی در فضا در محفظه پروفیل آلومینیوم بسته و برای نصب آسان و افقی در ریل آماده شده است اطلاعات مهم و وضعیت عملیاتی موجود از طریق LED ها...

By implementation of up to two (2) NTP LAN Boards 7273(RC) or NTP LAN Boards 7274(RC) (10/100/1000 Mbit/s autosensing, VLAN, Bonding, PRP) system 6844(RC) becomes a highly accurate NTP Stratum 1 Time Server fo synchronization of computers and industrial networks.

سرور دقیق هماهنگ سازی رایانه ها و شبکه های صنعتی By implementation of NTP LAN Boards 7273(RC) or NTP LAN Boards 7274(RC) (10/100/1000 Mbit/s autosensing, VLAN, Bonding, PRP) system 7001(RC) becomes a highly accurate NTP Stratum 1 Time Server for...

The receiver unit 4460 serves to synchronise the control devices with cyclic pulses.The data are emitted potential free. The unit can operate in a wide voltage range 12-60V DC (optional 36-75VDC).The electronic is placed in a plastic terminal box with screw terminals for the connections. The...

Module 4465 is a DCF77 clock in a compact aluminium housing for 35mm DIN rail mounting (DIN EN 60715 TH35). The module is easily clipped onto the rail via a clip based on "snap-in" mechanism.Module 4465 has a serial interface that is implemented in two (2) interface formats. There are five (5)...

Module 4475 is a Sub-Master Clock Module in a compact aluminium housing for 35mm DIN rail mounting (DIN EN 60715 TH35). The module is easily clipped onto the rail via a clip based on "snap-in" mechanism. The synchronisation of Sub-Master Clock Module 4475 can be performed via the following...

Module 6870 is a GPS clock in a compact aluminium housing for 35mm DIN rail mounting (DIN EN 60715 TH35). The module is easily clipped onto the rail via a clip based on "snap-in" mechanism. Module 6870 has two (2) individual and independent interfaces and is available in six (6) different...

Module 6875 is a GPS Time Server in a compact aluminium housing for 35mm DIN rail mounting (DIN EN 60715 TH35). It consists of a GPS clock module 6875 in an extended DIN Rail housing that have an additionally implemented NTP SINEC H1 LAN Board 7273 or an NTP SINEC H1 LAN Board 7274 (2 ethernet...

Compact - space-saving - highly precise - maintenance free! This is the hopf network timeserver 8030NTS/GPS, easily explained. With its up to 2 isolated and mutually independent network timeserver modules and up to 4 ethernet interfaces the network timeserver 8030NTS/GPS for DIN rail mounting is...

Switch-Box - System 5000 was designed and developed for setting up redundant clock systems in the 'hot standby function with automatic status-dependent signal switchover' operating mode. Switch-Box - System 5000 is used when the most stringent demands are placed on the availability of a clock...

نمایشگرهای بزرگ 4985 شامل یک ماتریس  16 در 16 دو خط 42 میلیمتری و یا یک خط 84 میلی متری هستند. آنها نمایش مقادیری مانند زمان بسیار دقیق و تاریخ را بر عهده دارند  The basic version of...

Mechanical structure of the antennaThe antenna is housed in a round weatherproof plastic casing. The casing cover is arched to prevent any rain water, snow or other impurities from settling on the antenna. The mechanical construction consists of sturdy, anodized aluminium or aluminium die-casting...

When outdoor antennas are used high interference voltage or current pulses may occur in the antenna cable during thunderstorms. This may result in damaging or destroying not only the directly connected radio-controlled clock system but also any other devices connected. To avoid severe damage and...

Passive GPS 2x Power SplitterIf only one GPS antenna can be installed (due to structural or other reasons), it is however possible to operate two GPS receivers with one common GPS antenna by using the passive GPS antenna splitter 4443. Voltage for Power Splitter 4443 is supplied internally by the...

If only one GPS antenna for operating several GPS receivers can be installed (due to structural or other reasons), it is however possible to operate up to 8 GPS receivers with one common GPS antenna by using the active GPS antenna splitter 4449. This solution is often used in the context of...

The line amplifier is integrated into an HF proof housing with a base plate. It is therefore easy to fix the device to the wall. The 6849 line amplifier is looped into the antenna cable. The voltage supply of the line amplifier is provided via the antenna cable by the BNC connector of the hopf GPS...

If several DCF77-clocks are wanted in the building the 4x antenna amplifier with potential separation can be used. The device is structured like the antenna amplifier FG444400, but without indirect lightning protection. The housing contains the mains unit and several amplifier modules. The signal...